PixelMate™ (C)#

MIPI CSI-2 (4-Lane) Pinout & Signal Assignments#

This pinout scheme applies to all sensors that natively output image data according to the MIPI CSI-2 standard. As by the definition in the MIPI standard, this layout provides 1x4 or 2x2 data lanes on the connector.

Note

Pixelmate connectors use serpentine pin numbering as opposed to the standard numbering method.

Pinout Legend | Signal Categories#

  • ⚡ Common Voltages - Standard power levels used across all configurations.

  • 🔋 Sensor-Specific Voltages - Voltage levels specific to the image sensor.

  • 📶 Sensor Signals - Communication and control signals for the sensor.

  • ⏰ Driving Clocks - Reference clocks for timing and synchronization.

  • 🔗 Data Lines - High-speed lanes for transmitting image data.

  • 🚫 Reserved / Secondary Signals - Unused or secondary signal paths.

Pin#

Signal

Pin#

Signal

1

⚡ 3V8

2

⚡ 1V8

3

⚡ 3V8

4

⚡ 1V8

5

🔋 V_ANA

6

🔋 V_DIG

7

🔋 V_ANA

8

🔋 V_DIG

9

📶 V_IF

10

📶 V_AUX

11

🚫 GND

12

🚫 GND

13

🚫 GND

14

🚫 GND

15

📶 RST_0

16

📶 RST_1

17

📶 SPI_MISO

18

📶 SPI_MOSI

19

📶 XMASTER0

20

📶 XMASTER1

21

📶 I2C_0_SCL

22

📶 I2C_1_SCL

23

📶 SPI_CS

24

📶 SPI_SCK

25

📶 XVS0

26

📶 XVS1

27

📶 I2C_0_SDA

28

📶 I2C_1_SDA

29

📶 XHS0

30

📶 XHS1

31

📶 XTRIG0

32

📶 XTRIG1 / FSTROBE

33

📶 PW_EN_0

34

📶 PW_EN_1

35

📶 SLAMODE1

36

📶 SLAMODE2

37

🚫 GND

38

🚫 GND

39

⏰ INCK

40

⏰ GPIO4 (MCLK2)

41

⏰ MCLK_1

42

⏰ GPIO5 (MCLK3)

43

🚫 GND

44

🚫 GND

45

⏰ D_CLK_1_P

46

🔗 D_DATA_3_P

47

⏰ D_CLK_1_N

48

🔗 D_DATA_3_N

49

🚫 GND

50

🚫 GND

51

🔗 D_DATA_0_N

52

🔗 D_DATA_1_N

53

🔗 D_DATA_0_P

54

🔗 D_DATA_1_P

55

🚫 GND

56

🚫 GND

57

🔗 D_DATA_2_P

58

⏰ D_CLK_0_P

59

🔗 D_DATA_2_N

60

⏰ D_CLK_0_N

Table 1: PixelMate™ (C) Pinout | MIPI CSI-2 (4-Lane) Signal Mapping

The table above shows the position of each signal on the 60-pin connector in case the image sensor provides it. For further details, please refer to the image sensor Datasheet.

Note

The table shows the general signal assignment that applies to all connections using PixelMate™ (C). The signals that are eventually available depend on image sensor and adapter configuration. Please use the FSM Connector Pinout from the individual FSM datasheet as reference for the available signals.