PixelMate™ (S)

Sub-LVDS, SLVS and SLVS-EC Pinout (8-Lane)

This pinout scheme applies to all sensors that natively output image data using signals according to Sub-LVDS, SLVS or SLVS-EC specification. This layout provides eight data lanes on the connector. Devices with SLVS and SLVS-EC share the same sensor package pins therefore share the same connector pins.

Note: Lane number assignment is applied according to SLVS numbering, which differs in most cases from the SLVS-EC lane numbering. Please refer to image sensor datasheet for correct SLVS-EC numbering.

Legend:

• ⚡ Common Voltages (from FPA to FSA)

• 🔋 Sensor Specific Voltages (from FSA to FSM)

• 📶 Sensor Signals

• ⏰ Driving Clocks

• 🔗 Data Lines

• 🚫 Reserved / Secondary Signals

Pin#	Signal	Pin#	Signal
1	⚡ 3V8	2	⚡ 1V8
3	⚡ 3V8	4	⚡ 1V8
5	🔋 V_ANA	6	🔋 V_DIG
7	🔋 V_ANA	8	🔋 V_DIG
9	📶 V_IF	10	📶 V_AUX
11	🚫 GND	12	🚫 GND
13	🚫 GND	14	🚫 GND
15	📶 SDA	16	📶 SCL
17	📶 SDO	18	📶 XCE
19	📶 TOUT0	20	📶 SLAMODE
21	📶 TOUT1	22	📶 XMASTER
23	📶 TOUT2	24	🚫 NC
25	🚫 NC	26	📶 XTRIG
27	🚫 NC	28	📶 XHS
29	🚫 NC	30	📶 XVS
31	🚫 GND	32	🚫 GND
33	📶 RST	34	🔗 D_DATA_7_P
35	⏰ MCLK	36	🔗 D_DATA_7_N
37	🚫 GND	38	🚫 GND
39	🔗 D_DATA_6_P	40	🔗 D_DATA_5_P
41	🔗 D_DATA_6_N	42	🔗 D_DATA_5_N
43	🚫 GND	44	🚫 GND
45	🔗 D_DATA_4_P	46	🔗 D_DATA_3_P
47	🔗 D_DATA_4_N	48	🔗 D_DATA_3_N
49	🚫 GND	50	🚫 GND
51	🔗 D_DATA_2_P	52	🔗 D_DATA_1_P
53	🔗 D_DATA_2_N	54	🔗 D_DATA_1_N
55	🚫 GND	56	🚫 GND
57	🔗 D_DATA_0_P	58	⏰ D_CLK_0_P
59	🔗 D_DATA_0_N	60	⏰ D_CLK_0_N

Table 1: Standard Pinout of LVDS (8-Lane) interface

The table above shows the position of each signal on the 60-pin connector in case the image sensor provides it. For further details, please refer to the image sensor Datasheet.

Note: The table shows the general signal assignment that applies to all connections using PixelMate™ (S). The signals that are eventually available depend on image sensor and adapter configuration. Please use the FSM Connector Pinout from the individual FSM datasheet as reference for the available signals.